雷蒙磨的使用并不是说你只会简单的操作就行了，这里面的学问还是有很多的，比如说关于磨粉机的保养、磨粉机的检液备桐修、磨粉机的基本工作原理等一些方方面面的知识，今天我们先来说说如何减少雷蒙磨故障的四大学问。
一、保证正常的工作载荷，要滚伏注意不能在超过机械所能承受的最大负荷下进行工作，要在力所能及的情况下使用机械。
二、保证对机械的合理润滑，要合理选用润滑闹坦剂，要根据机械的种类和应用结构的不同选用正常的润滑剂类别，根据机械的要求选用合适的质量等级，根据机械的工作环境和不同的季节选择合适的润滑剂牌号。
三、适时维修，在使用过程中要加强对雷蒙磨粉机等制粉机械的定期与不定期检查，及时了解机械的运行情况，对临时出现的故障，要及时进行处理，不要因故障小、不影响使用而延误维修时机，酿成更大故障。
四、采取正确的技术措施和组织管理措施。
其实我们的雷蒙磨粉机在平常的生产过程中遇到的一些小毛病是可以做到防患于未然的，只要你做到正确合理地进行定期与不定期保养，保持机械的清洁、干净，定期检查机械的技术状态，发现异常及时处理，对于松动和失调的零部件及时紧固和调整，对一些易损件进行预防性的更换等等，其实很多小问题是可以不发生的。
1、雷蒙磨启动前，检查磨内有无铁屑等杂物，检查螺栓、螺母是否松动，特别是主机内的螺栓、螺母是否松动，严格检查各检修门是否关严，调整风机、主机方向，排气虚毕门应全开。
2、启动顺序是先启动分析仪，然后启动风机，然后启动主机。主机启动后，应立即添加物料（先添加细颗粒物料，再添加普通颗粒物料），然后打开大流量气阀，在保证进出口不发生喷溅的前提下，尽可能关闭小排气阀，然后调整成品细度。
3、带颚式破碎机和提升机的粉磨生产线在启动前应检查破碎机的颚隙是否符合进料尺寸，并将分析仪的速度调整到接近尺寸要求。
4、最后，按以下顺序启动机器：启动斗式提升机-启动颚差腔芹式破碎机-启动分析仪-启动鼓风机（空载启动，正常运行后加载）-启动主机，启动主机后立即启动电磁振动给料机，然后开始研磨工作。操作顺序简单如下：启闭机-破碎机-分析仪-风机-主机-给料机。
5、停机时，应按以下顺序停机：关闭进料机停止进料；大约一分钟后停止主机；吹净剩余物料后停止鼓风机；最后关闭分圆纤析仪。停机顺序为：给料机-主机-鼓风机-分析仪。（注：启闭机将一定数量的物料运至仓库后，先停止破碎机，然后停止提升。存储取决于需求。
6、雷蒙磨粉机在正常运行中不允许随意加油。为保证生产安全，当磨机任何部位出现异常噪音或负荷突然增加时，应立即停机检查排除故障，以免发生重大事故。当机器再次启动时，必须取出所有剩余的材料。否则，机器启动时电流会过大，严重时会影响启动甚至烧毁设备。
第一：正常情前亩仿况下，硬度越高，产量越低，物料硬度的提高就会降低雷耐滑蒙磨的生产效率，对雷慧纤蒙磨的零件磨损也会加大。
第二：物料的粘度越大，吸附能力就越高，不被风选的可能性就会增大，降低雷蒙磨效率
第三：物料的湿度：雷蒙磨适用湿度在6%以下的产品。含水量高的物料在磨粉之后就会粘在雷蒙磨内部，在输送中也会造成堵塞，明显就会对雷蒙磨的效率造成了影响
第四：物料的组成：雷蒙磨正常使用可以出粉的细度在80-325目之间，如果物料中含有较多细粉，就会附着在雷蒙磨内壁上，好是在此之前过一次振动筛，筛选出适合雷蒙磨粉机制粉的尺寸好。
The general maintenance of the Raymond Mill is to do 1, the mill in use, there should be fixed personnel responsible for custody, operators must have a certain level of technology. Mill operators must be given the necessary technical training before installation to make them familiar with the Reymond Mill's principle and performance, and the operating procedures 2. In order to make the mill normal, it is necessary to work out the safe operation system of equipment maintenance to ensure the long-term safe operation of the mill. At the same time, it is necessary to have the necessary maintenance tools, lubricating grease and corresponding accessories.\,\speak_url\:{\speak_url\:\/audiofrom=zh&to=en&voice=2&cate=speakUrl&key=fbadbb466d4cf5b7ca922aa71967880e&query=我们甲浦瑞机械一般对雷蒙磨粉机的保养是要做到 1、磨粉机在使用过程当中，应有固定人员负责看管，操作人员必须具备一定的技术水平。磨粉机在安装前对操作人员必须进行必要的技术培训，使之了解雷蒙磨粉机的原理性能，熟悉操作规程。 2、为使瞎局磨机正常，应制定设备“设备保养安全操作制度”方能保证磨机长期安全运行，同时要有必要的检修工具以及润滑脂和相应的配件。\,\卜并tSpeak_url\:\/audiofrom=zh&to=en&voice=2&cate=tSpeakUrl&key=abc6c2eff3e3e74894f630d2fb52536e&query=The general maintenance of the Raymond Mill is to do 1, the mill in use, there should be fixed personnel responsible for custody, operators must have a certain level of technology. Mill operators must be given the necessary technical training before installation to make them familiar with the Reymond Mill's principle and performance, and the operating procedures 2. In order to make the mill normal, it is necessary to work out the safe operation system of equipment maintenance to ensure the long-term safe operation of the mill. At the same time, it is necessary to have the necessary maintenance tools, lubricating grease and corresponding accessories.,speak_url:{磨弊让speak_url:/audiofrom=en&to=zh&voice=2&cate=speakUrl&key=31073c0e8476b93b92ece522dddc40d7&query=The general maintenance of the Raymond Mill is to do 1, the mill in use, there should be fixed personnel responsible for custody, operators must have a certain level of technology. Mill operators must be given the necessary technical training before installation to make them familiar with the Reymond Mill's principle and performance, and the operating procedures 2. In order to make the mill normal, it is necessary to work out the safe operation system of equipment maintenance to ensure the long-term safe operation of the mill. At the same time, it is necessary to have the necessary maintenance tools, lubricating grease and corresponding accessories.\,\speak_url\:{\speak_url\:\/audiofrom=zh&to=en&voice=2&cate=speakUrl&key=fbadbb466d4cf5b7ca922aa71967880e&query=我们甲浦瑞机械一般对雷蒙磨粉机的保养是要做到 1、磨粉机在使用过程当中，应有固定人员负责看管，操作人员必须具备一定的技术水平。磨粉机在安装前对操作人员必须进行必要的技术培训，使之了解雷蒙磨粉机的原理性能，熟悉操作规程。 2、为使磨机正常，应制定设备“设备保养安全操作制度”方能保证磨机长期安全运行，同时要有必要的检修工具以及润滑脂和相应的配件。\,\tSpeak_url\:\/audiofrom=zh&to=en&voice=2&cate=tSpeakUrl&key=abc6c2eff3e3e74894f630d2fb52536e&query=The general maintenance of the Raymond Mill is to do 1, the mill in use, there should be fixed personnel responsible for custody, operators must have a certain level of technology. Mill operators must be given the necessary technical training before installation to make them familiar with the Reymond Mill's principle and performance, and the operating procedures 2. In order to make the mill normal, it is necessary to work out the safe operation system of equipment maintenance to ensure the long-term safe operation of the mill. At the same time, it is necessary to have the necessary maintenance tools, lubricating grease and corresponding accessories.,tSpeak_url:/audiofrom=en&to=zh&voice=2&cate=tSpeakUrl&key=31073c0e8476b93b92ece522dddc40d7&query=The general maintenance of the Raymond Mill is to do 1, the mill in use, there should be fixed personnel responsible for custody, operators must have a certain level of technology. Mill operators must be given the necessary technical training before installation to make them familiar with the Reymond Mill's principle and performance, and the operating procedures 2. In order to make the mill normal, it is necessary to work out the safe operation system of equipment maintenance to ensure the long-term safe operation of the mill. At the same time, it is necessary to have the necessary maintenance tools, lubricating grease and corresponding accessories.\,\speak_url\:{\speak_url\:\/audiofrom=zh&to=en&voice=2&cate=speakUrl&key=fbadbb466d4cf5b7ca922aa71967880e&query=我们甲浦瑞机械一般对雷蒙磨粉机的保养是要做到 1、磨粉机在使用过程当中，应有固定人员负责看管，操作人员必须具备一定的技术水平。磨粉机在安装前对操作人员必须进行必要的技术培训，使之了解雷蒙磨粉机的原理性能，熟悉操作规程。 2、为使磨机正常，应制定设备“设备保养安全操作制度”方能保证磨机长期安全运行，同时要有必要的检修工具以及润滑脂和相应的配件。\,\tSpeak_url\:\/audiofrom=zh&to=en&voice=2&cate=tSpeakUrl&key=abc6c2eff3e3e74894f630d2fb52536e&query=The general maintenance of the Raymond Mill is to do 1, the mill in use, there should be fixed personnel responsible for custody, operators must have a certain level of technology. Mill operators must be given the necessary technical training before installation to make them familiar with the Reymond Mill's principle and performance, and the operating procedures 2. In order to make the mill normal, it is necessary to work out the safe operation system of equipment maintenance to ensure the long-term safe operation of the mill. At the same time, it is necessary to have the necessary maintenance tools, lubricating grease and corresponding accessories.